Eod Hook set

Technical Parameters 1. Outline Size: (length × width × thickness)210mm × 75mm × 40mm 2, pulley diameter: Φ50MM 3, applicable rope diameter: Φ4 ~ Φ10MM 4, lifting weight: 35kg 5, weight: 700G

The main components include: 1. The main rope spool: The main rope of Φ5 × 120 meters is wound on the Spool, and the end of the Spool is equipped with a detachable stainless steel spring hook. The spool is arranged on the Spool, and when the Spool is taken up, the Spool can be taken down and inserted into the plastic card sleeve beside the handle. 2. Nylon rope with Sheath (white) nylon rope is made of multi-ply polypropylene fiber with Φ70 soft rope sleeves at both ends. The main rope and fixed pulley can be used to pull the object after the binding object is tightened by the Lasso. 3. Steel wire rope with sleeve: the steel wire rope is made of multi-strands galvanized steel wire with Φ10 rope sleeves at both ends, and the rope buckle is riveted by stainless steel sleeve. Use a lasso to bind the object tightly, and the hook should be hung on the Lasso with retaining ring. Serial number, rope diameter, length, weight, load 11.5 mm 2000MM 50G ≤180kg22mm 2000MM 80G ≤300kg33mm 2000MM 150G ≤500KG 4. Rope gripper: The groove of Rope gripper is formed by two conodont plates. Use this tool to avoid rope slippage during rope laying and traction of suspected explosives. 5, Hooks: Hooks made of stainless steel, non-ferromagnetic, rectangular cross-section, the shape of a single hook and double hook two kinds. The outer surface is sprayed with yellow plastic. Serial number, hook shape, outline size, hook mouth size, connecting thread number 1 single hook 120 * 70 * 1550m1012 single hook 80 * 38 * 1525m1013 single hook 57 * 20 * 1314m1014 Double Hook 75 * 58 * 3825 * 2m101。6, FORCEPS: FORCEPS are made of steel plate, adjustment screw end with a lifting ring, jaw size is adjustable. According to the size of the clamp, the size of the clamp should be adjusted in advance, the right screw clamp smaller, but can not < 170mm, otherwise the clamping function is invalid. The gripper can be locked after the object is clamped, and can be pulled by a rope pulley and a hook. Technical data: maximum jaw size: 38mm jaw length: 245mm jaw minimum size: 17mm weight: 450G7, eye ring: ring with 25mm long wood screw, hand-screw eye ring fixed to a wooden object as a fixed point, the quantity of the eye socket installed on the woodwork depends on the force, and the force can be installed 2 ~ 3. Lifting Ring: The lifting ring made of stainless steel, connecting thread M10, surface spray plastic, and stainless steel hook connection, can make hook into a hook with lifting ring. 9. Sling: The sling is made up of 80 × 2 Nylon Braid and nylon cord. This sling is suitable for binding, wrapping and cylindrical objects. A belt of the same type. Hook the main rope with a nylon noose before lifting. Technical data: Bandwidth = 80mm strip length = 1200mm strip weight = 200g Max load: 100kg bundle object diameter ≤ φ350mm10 shackle: Lifting ring made of stainless steel. The PIN has an M5 thread at one end, which can be removed after loosening to become an opening hook. The lifting ring can be matched with two kinds of fixed pulley and clamping device in the set of explosive discharger. In particular, the pulley can not be directly suspended, the use of this ring as a transitional connection.

Technical data: width = 12mm throat = 12.5 mm perforating aperture ≥6.5 mm maximum load ≤35kg11 wedge: Wedge Nails made of Chromium Alloy Steel, with high strength and toughness, shape is divided into single hole and double hole, double hole into 90 degrees each other. Wedges can be wedged into walls, brick joints, and other earth building materials. In open spaces, such as parking lots, they can become fixed points or pull piles. Technical data: 1, Wedge Nails should be wedged into the solid no loose foundation. 2. Wedges are ferromagnetic. A crossbar with an adjustable pitch that supports a door or window. There are two hanging holes on the pole for hanging pulley or rope, a spring post pin and a micro distance adjusting screw on the pole, and two nylon supporting feet at each end of the pole. Whether or not to use the supporting feet depends on the material of the door frame or window frame and the irregularity, a concrete or brick wall with a flat surface and two ends of a Strut can be used simultaneously. If the wall surface is uneven or the wooden structure can not use the supporting foot, the needle rod of the pole end is directly inserted into the wall surface, the length of the three needle rods of the left end of the supporting rod can be adjusted, and its adjustment method is to use an inner hexagon wrench with the body size of 3mm to extend into the screw hole, find the inner hexagonal hole of the needle bar and rotate it. With one hand, push the pin down to level with the outer ring of the Rod Sleeve. With the other hand, pull the adjusting rod of the inner tube slightly less than the width of the door frame or window and place it horizontally, the left-hand screw tightens the bar again. When supporting the crossbar, the handle can be moved through the screw hole to rotate more labor-saving.

Technical Data: Minimum Dimension of stay bar: 705mm stay bar maximum dimension: 1150mm stepless adjustment length range: 745 ~ 1180mm weight: 1.5 kg load bearing: when span ≤900mm ≤20kg13, slide bar clamp: a slide bar with two movable arms, each clamping arm is provided with a t-shaped screw to adjust the angle between the arm and the crossbar. The right-handed t-shaped screw can cause the two clamping arms to close together to clamp the clamping object. The left-handed t-shaped screw can loosen both arms to remove the clamping device. There are three Φ8 holes on the sliding rod for loading and unloading rings or pulleys. The M6 screw hole at the end of the clamping arm can be installed with three kinds of clamping blocks (circular plane clamping block, l-shaped clamping block and v-shaped clamping block) . The use of these three kinds of clamping blocks depends on the surface state of the main body being clamped. If the large plane available plane clamp block, narrow or window frame with the l-shaped clamp block, cylindrical surface with a v-shaped clamp block.

Technical Data: Arm clamp opening size: 200mm arm clamp depth: 130mm。Detachable pulley: The detachable pulley is composed of a hook, a wheel frame, a pulley, an elastic bead and a splint. The pulley is used in conjunction with a ball clip and a rope. Use of this pulley is particularly necessary at the scene of an incident where multiple turns are required to drag the suspect explosive from a hidden area to an open area. The pulley should be set at the turning point of the transportation route, such as the door, the window, etc. . At this point, a ball clip is installed on the front rope of the first pulley (the pulley closest to the explosive) before the suspected explosive is towed by the support bar as a hanging point, when the clamp is moved to the pulley (where the suspect explosive is dragged under the PULLEY) and hits the splint and pushes it apart, the rope detaches from the pulley and continues to drag, with the second pulley becoming the main pulley. Continue to move suspected explosives until you reach your destination.Fixed pulley with locking device: The pulley with locking device is composed of a hook, a roller, a wheel frame and a locking device. The pulley and the locking device (conodont plate) are made of Nylon 6, and the wheel frame is made of duralumin plate. When in use, first stagger the roller plate to expose the locking device, then pull the conodont plate to widen the gap between it and the roller, and then hang the main rope into the groove of the wheel, the conodont plate is reset, the wheel plate is restored to its original state and locked with the Spring Pin. When lifting, the main rope is pulled forward without any hindrance. When lifting to a certain height to stop the pulling rope, the rope is pulled backward by the weight of the lifting object.16. Main Lock: In the process of removing suspicious explosives at the scene of the accident, at certain turning points, it is not easy to use braces to hang the pulley, (such as in the corner of the wall, or near a large area of the wall) wedge nails into the wall can hang the main lock on the wedge hole, the main lock can be threaded directly into the nylon rope as a fixed pulley, the smooth outer surface of the rope will not have too large wear. Before hanging the main lock, press the spring lever by hand. When the main lock is notched, hang it into the keyhole and then lock the main lock.17. The connecting rod is divided into two kinds, one is the end with two fixing pins, which is connected with the anti-release Hook and long lapped rod middle piece, the other is with long slot, which is connected with the Anchor Hook and long rod middle piece.

Technical Data: Connection Screw Hole: M10 outline size: Φ13 × 80(with long groove) Φ12 × 60(with double locating needle)18. LINE CLAMP: Aluminum Hook head screw mounted on the box with line groove, adjust the nut on the hook screw to fasten the block to any part of the rope. The end of the hook screw rod has a Φ16 ring to be used for fastening the rope or hanging the pulley. 19. Ball Clip: The ball clip is made of aluminum alloy. Two semicircular clips are connected by a screw Rod. The gap between the left clip and the left clip is enlarged. The nylon rope is put into a slot inside the clip, and then the right clip clips the rope. The utility model can be used in conjunction with a detachable fixed pulley. When the clamp block runs to the fixed pulley, the splint of the detachable pulley will be squeezed away, and the rope will fall off naturally. 20, viscous fixed plate: viscous fixed plate is made of 2mm thick duralumin plate, the shape of a square, there is a round hole on the back of the adhesive, you can freely paste the fixed plate in a flat clean surface without holes. Such as walls, ceilings, doors, cabinets, desktops and so on. The φ15mm hole on the board is used for fastening, and a sticking board can be used as a fixed point.

Technical Data: Adhesive Area: 90mm × 90mm-30mm × 30mm weight: 15g fixed under ideal conditions, load 5kg21, vacuum sucker: the main body is made of cast aluminum alloy, the middle of the cross beam has φ16 rings, there are two φ115mm rubber suction pads, the center distance is 200mm. The Vacuum Cup must be adsorbed on a smooth, flat, impermeable surface, such as building doors, glass, furniture, filing cabinets, vehicle doors, windows, etc. . Before the adsorption, the lever on each sucker is lifted, and the disk is laid flat on the adsorption body, and the main body can be absorbed by putting down the lever. Each sucker can be used as a point of attachment or fixation.

Technical Data: Suction Cup diameter: Φ115MM Suction Cup Quantity: 2 Lifting Ring Aperture: Circle Diameter: φ16mm outline size: length × width × height: 400mm × 115mm × 110mm weight: 1.1KG22, DUSTPAN: When suspicious loose is found in the scene of explosion, the utility model can be first put into a Dustpan and dragged to the destination by hook rope and pulley facilities. Before using the Dustpan, the relevant parts are connected with the Nylon Hasp, and the main rope hooks are hung on the hasp in the composite dustpan shape.

Technical Data: Internal Dimension: Length × width × height 580mm × 310mm × 160mm 23, anti-release Hook: anti-release Hook is a kind of hook with locking spring, suitable for soft package of Hook, such as package of suspicious explosive. The Hook can not be released as long as the object is hooked and the door is closed by a latch spring. There is a ring on the hook. The main rope hook can be hung here in advance.

Technical Data: Outline Size: Hook 135mm × 80mm × 12mm, Hook 110mm × 80mm × 12mm. Drag weight 50kg, lifting weight 35kg weight: Big Hook 50g, small Hook 30g 24, Anchor Hook: Anchor Hook is divided into two kinds, three hook and five hook, the hook has barb, once the target can not escape. The Anchor Hook is provided with a circular ring, where the main rope is hung before the anchor object, and then the hook is placed in the long slot of the tie rod before the tie rod to send the anchor Hook to the target. If the Anchor Hook with the main rope can be directly thrown to the target without a tie Rod, it is more convenient to use the five-hook type Anchor Hook.

Technical Data: Outline Size: Big Hook Φ65 × 60 small Hook Φ38 × 50 tow weight: Big Hook 5kg small Hook 3kg 25, implementation standard: Meet the requirements of “Ga 975-2012 terms of special police equipment”, to provide the inspection report issued by the Ministry of Public Security’s authoritative inspection organization (National Product Quality Supervision and Inspection Center for security prevention alarm system (Beijing) and the Ministry of Public Security’s electronic product quality inspection center) .

Process and materials: the Rope Hook set is the most ideal disposal equipment for explosive disposal by EOD personnel. It avoids the direct contact between the explosive suspect and the explosive suspect, and transfers and identifies the explosive suspect through the long-distance operation, thus effectively ensuring the safety of the explosive suspect. Rope Hook Tool Group: equipped with a variety of rope, pulley, fixing tools, fixtures, Suction Cup, expandable Rod, Cat Hook and other tools, can be assembled with each other.

Colors and styles can be customized